PRP Kits for Hair Restoration: Sizing, Hardware & Specification Checklist

AdminMy Store

Reading time: ~9 minutes | Target audience: Trichology clinics, hair restoration surgeons, aesthetic practices adding scalp protocols
Last updated: Nov 12, 2026

Introduction

Scalp protocols are the most consumable-intensive application of PRP in routine practice. A facial treatment is usually a single pass over a defined area; a hair restoration course is a series of sessions, each covering a diffuse field, often at multiple depths, and often on a schedule that runs for months.

That changes what a kit needs to be. The tube chemistry questions are the same as anywhere else, but the quantities, the delivery hardware and the failure modes are not. A kit assembled for facial work will function on a scalp, and it will waste money doing so.

This page sets out what a PRP kit for hair restoration should contain, how to size it against a session schedule, and which specification choices actually change the preparation. The tube-level detail sits in PRP tubes for hair restoration.

1. Why scalp work consumes differently

Parameter Facial protocol Scalp protocol
Treatment area Usually under 100 cm², often focal Diffuse — frequently the whole vertex and mid-scalp
Session structure Frequently a single session or short course Multi-session course with maintenance intervals
Delivery Intradermal injection, cannula or microneedling Intradermal injection at depth, or microneedling, or both in one visit
Consumables per visit 1–2 tubes typical 2–4 tubes typical, depending on field size
Cost sensitivity Lower — per-session cost is amortised over a higher-value treatment Higher — per-session consumable cost is a larger share of the total

The consequence is straightforward: on a course of six sessions, a kit that wastes one tube per visit wastes six tubes. On the scalp, quantity discipline matters more than it does on the face.

2. Volume and tube size for scalp work

The starting blood volume you need is set by the area being covered and the delivery method, not by a fixed protocol rule. Two figures are useful for sizing:

  • A 10 ml tube yields roughly 2–3 ml of PRP after separation.
  • Diffuse scalp injection typically uses more finished volume than a focal facial treatment, because the field is larger and the injection grid is wider.

That generally puts a scalp session in the 2–4 tube range, and makes the 10 ml and 12 ml formats the practical workhorses. Both share the 16 mm outer diameter of every other tube in the range; the difference is length — 10 ml at 16 × 100 mm, 12 ml at 16 × 120 mm — which is what the rotor constrains. If your centrifuge takes the shorter tube but not the longer one, the 12 ml option is not available to you regardless of preference.

The full size and material comparison is in PRP tube sizes, volumes and materials.

3. The delivery method decides what the kit must contain

This is where hair kits diverge most, and where generic kits most often fall short.

Intradermal scalp injection needs fine-gauge needles or a blunt cannula suited to the depth of the target layer, and a syringe the practitioner can control for a grid of many small aliquots. A kit supplied with a single large syringe and one 21G needle is not built for this.

Scalp microneedling applies PRP topically through micro-channels rather than injecting it. The requirement shifts from injection hardware to volume and flow: you need enough finished PRP to keep the treatment field wet across multiple passes, and the preparation needs to be free of red cell contamination because it is spread across a large visible surface. That makes the gel separator configuration the more suitable choice — the reasoning is set out in how the gel separator works, and the microneedling selection logic in PRP tubes for microneedling.

Combined protocols — injection followed by microneedling in the same visit — need both, which is the case for specifying the tray yourself rather than accepting a pre-packed kit.

Practical note: if the same clinic runs both facial and scalp work, the sensible kit structure is one tube specification that serves both, plus a separate injection-hardware selection per protocol. Splitting the kit per application duplicates stock and multiplies lot numbers for no clinical gain.

4. Anticoagulant and separation choice for scalp protocols

For injected scalp work, the anticoagulant decision follows the same logic as any intradermal application. ACD-A is the common default in aesthetic practice: it chelates calcium reversibly, so activation remains possible if the protocol calls for it, and it does not degrade the growth factor content of the plasma. Sodium heparin is the alternative where a different working window or handling characteristic is preferred.

The detailed comparison — including how each anticoagulant affects platelet integrity and working time — is in PRP tube anticoagulants compared. If your practice also runs PRF, note that PRF tubes carry no anticoagulant at all and are a different product family with a different workflow; the two are compared in PRP vs PRF tubes.

5. Sizing a first order

Size the order against the course, not against the single visit:

  1. Count the course. Sessions per course multiplied by tubes per session gives the consumable requirement for one patient cycle.
  2. Add the validation run. Before committing, run one box of each candidate size through your own centrifuge with your own protocol. Rotor fit and separation behaviour are worth confirming on your machine rather than on a specification sheet.
  3. Check the expiry against the course length. A multi-month course is only economical if the remaining shelf life covers it. Ask for the remaining shelf life at shipment, in writing. Storage requirements are covered in PRP tube storage and shelf life.
  4. Confirm the lot traceability route. Every session should be recordable against a tube lot number.

6. Specification checklist for a hair restoration kit

Item What to confirm
Tube configuration ACD-A + gel separator, or the alternative your protocol specifies — stated explicitly, not implied
Volume and dimensions Stated as both volume and mm dimensions, so rotor fit can be checked
Tubes per kit Tube count stated separately from total item count
Injection hardware Gauge and length suited to scalp intradermal work, or explicitly excluded
Sterilisation Method declared, single-use, individually packaged
Remaining shelf life Guaranteed at shipment, sufficient to cover the course
Device status CE-marked medical device manufactured under ISO 13485 — not a diagnostic tube

The documentation that should accompany each of these is set out in our CE marking guide, and the audit-side view in how to verify a manufacturer's certification.

Frequently asked questions

How many tubes does one hair restoration session need?

Typically two to four, driven by field size and delivery method rather than by a fixed protocol figure. A 10 ml tube yields roughly 2–3 ml of PRP after separation; a diffuse scalp field usually consumes more finished volume than a focal facial treatment.

Can I use the same kit for facial and scalp treatments?

Often yes for the tubes. The difference is usually in the delivery hardware — needle gauge, cannula type, syringe control — rather than in the tube. Practices running both applications usually source tubes in a single specification and select injection hardware per protocol.

Is a gel separator necessary for scalp work?

It is strongly preferable where the PRP is applied topically through microneedling, because red cell contamination is visible across a large surface. For injected work the argument is about consistency rather than appearance, but the same tube is usually the practical answer.

Does the tube size affect the outcome of a scalp protocol?

Tube size affects how much starting blood you draw and therefore how much finished PRP you have to work with. It does not change the concentration achieved by a given protocol. Choose the size that matches the area and the delivery method, and confirm it fits your rotor.

What is the most common purchasing mistake on hair kits?

Buying a kit sized for facial work and then under-drawing for a diffuse scalp field, or buying a large format tube that the clinic's centrifuge rotor cannot accept. Both are avoided by checking tube dimensions against the rotor before ordering.

Disclaimer: This page provides consumable and specification information for healthcare professionals. It does not constitute medical advice, and it does not describe a treatment protocol or claim a clinical outcome. Treatment parameters, session schedules and centrifugation settings must follow your own validated protocol, the device instructions for use and local regulatory requirements.

Related reading: PRP tubes for hair restoration — tube-level selection for scalp protocols · PRP tube sizes, volumes and materials · PRP tubes for microneedling · PRP kits guide.

For CE-marked, ISO 13485-manufactured PRP tubes and kits in the volumes used for scalp protocols, browse the PRP kit collection or contact our team with your session schedule and rotor model.

Regresar al blog

Deja un comentario